Vibrating Crotch and Breast Ropes |
 |
| TITLE |
+ |
- |
| FILE NAME |
+ |
- |
| DATE |
+ |
- |
| POSITION |
+ |
- |
|
|

Vibrating Crotch and Breast Ropes10006 viewsCrotchropes are always fun, but they are especially fun when they vibrate. This tutorial explains how to make vibrating crotchropes, and how to use the same techniques to make vibrating breast ropes.
|
|

Step 92241 viewsGoing counter-clockwise around the circle, gently pull on each strand, removing some slack. Don’t try to remove it all at once, or you will pull the knot out of shape. Instead, go around the circle several times, taking out a little more slack each time. When you are done, you should have a symmetrical six-sided figure.
Repeat the above procedure to make a second layer.
|
|

Step 82360 viewsKeep doing this till you have done all six strands. The last end goes through the loop around your index finger (from the first strand you worked with). The strand goes in the direction opposite to the way your index finger is pointing.
|
|

Step 72306 viewsStick out your index finger, and make sure that one strand is draped over it. Take this strand and, going counter-clockwise, lay it over the next strand. Take that strand, and again going counter clockwise, lay it over the next strand.
|
|

Step 62528 viewsHold the knot in your right hand, with the loops pointing down, and arrange the six ends so that they are draped over your fist and evenly spaced.
|
|

Step 52304 viewsReach through the loop and pull then ends through it. Take a moment to groom the knot so that the ropes lie smoothly.
|
|

Step 42538 viewsRun the ends so that they cross over the ropes, forming a loop.
|
|

Step 32488 viewsGrab the six ends, about seven inches from your finger, so you have a fist with three loops sticking out.
|
|

Step 231628 viewsNow take the ends, and run them over the rope next to the hole and through the braid to the other side. Turn the braid over and do it again. You are weaving the ends over and under through the braid. This makes the loop secure, and also makes the unsightly ends disappear.
Keeping the vibrating breast rope in place can be tricky. It works best if your partner is lying on her back, and if she has large breasts. If you already have a breast harness on her, you can add ropes that attach to the breast harness below the breasts, loop around the vibrating rope, and attach to the top of the breast harness. This will keep the breast rope properly located.
Now, turn on the breast vibrators, turn on the crotchrope vibrator, and give your partner an experience she won't forget.
|
|

Step 221608 viewsTo make the end loop, find a spot about four inches back from where you stopped braiding. Gently pull the braid apart at that point, so you have a hole on each side of the braid. Bend the braid around to form a loop, sticking the three left-hand ropes through the hole on the left side, and the three right-hand ropes through the hole on the right side. Pull them snug, so you have a nice loop in the braid.
|
|

Step 211963 viewsThe same technique for making crotchropes can be used for making a vibrating breast harness. You will need one more bullet vibrator and another condom. (Alternatively, you can use one of those double bullet vibrators, or even vibrating nipple clamps. With the vibrating nipple clamps, the clamp part is covered up by the braid, and they act like ordinary vibrators.) Follow the crotchrope directions, but when you get to the herringbone braid, braid only about six inches. (The exact distance will vary with the spacing of your partners’s breasts.) Now grasp the end of the braid in your right hand, arrange the six ends so they drape evenly over your fist, and repeat the procedure you did to enclose the first vibrator. When you get the vibrator enclosed, you can go back to the herringbone braid.
If you have long ropes, you can extend the braid far enough that you can run it around your partners’s back, run the end through the original loop, and tie it there. Here is an alternative approach. You can make a loop on the end of the rope, then use a single rope run behind her back to tie the loops together. This will be more comfortable if she is on her back, because she has only two ropes, rather than a thick braid, to lie on.
|
|

Step 206070 viewsTo use the crotchrope, you can tie a waist rope around your partner, running the waist rope through the loops on the crotchrope, or you can tie the loop to the waist rope with a short length of rope. Run the rope between the legs, and over the waist rope in back. If your partner is standing, you can unbraid the crotchrope to where it meets the waist rope, and tie a knot there. If she is lying on her back, it is better to run the end of the crotchrope over the waist rope, and back down between the legs. This causes less of an uncomfortable bump for her to lie on.
Even so, you may have to put a pillow under her buttocks so she isn’t lying on the bump. With your partner lying on her back, you don’t even need to tie the end of the crotchrope. The bumpiness of the braid, and the fact that she is lying on the waist rope, will hold it in place. You can pull on the end to tighten it up, and it will stay tight.
Now, restrain your partner as desired, turn on the vibrator, and enjoy.
|
|
|
|