| Top rated |
Step 182317 viewsYou can continue bringing the ends around under the balls, then crossing them at the top. Each turn will put a little more pressure on the balls. You can continue this till you run out of cord, or you can take the ends and use them as a leash, or tie marling-hitches around the cock with them. (See the Marling-hitch CBT tutorial.)
Enjoy...
(37 votes)
|
|
Step 82145 viewsNow cross the right rope over the left, and you’re done.
This tie works like the old Chinese finger trap toys or like an electrician's cable grip. As you pull on the ropes, the crossed ropes tighten up, gently gripping the hair without putting too much stress on it. One thing you have to be careful of is not putting the reef knot too close to the end of the hair. As you pull on the ropes, the crossed ropes stretch out as they contract, and if the reef knot is too close to the end of the hair, it will slide off.
To remove the hair tie, release the tension in the ropes, then grip the top of the assembly and slide it down the hair. It will slide right off. (When we presented this at Shibaricon 2007, a Domme with beautiful long hair told us that she uses that same technique to tie ribbons in her hair. If someone tries messing with her by pulling on her ribbons, she can just grab the top and release them.)
I hope you enjoy this tie as much as I do.
(36 votes)
|
|
Step 10987 viewsNow stretch the large-size condom so covers both the head of the Hitachi and the cock, and roll it down. With a real cock, rather than the fake one we are using here, you will be able to roll it down a little farther, and it will tend to stay in place. You don't have to be too careful about putting the Hitachi on the sensitive part of the cock. The vibrations are strong enough that close is close enough. Place the handle of the Hitachi between your partner's legs, and tie them together. This supports the Hitachi so the cock doesn't have to, and keeps it from flopping around. You should should probably have your partner tied down, too.
Now turn the speed control switch to variable speed, and the control knob to zero, and the Hitachi switch to low. Slowly turn up the speed control knob. You will notice that the character of the vibrations change with the speed, and that somewhere around half way, the vibrations are actually stronger (though slower) than when it is turned all the way up.
Now you can play with the speed control, making it slow enough to keep the cock hard, but not enough for orgasm, for as long as you want to tease your partner. Or you can try speeding it up every now and then, but backing off just before orgasm. And if you are into forced orgasms, and post-orgasmic stimulation, you can leave it running for a while afterwards.
And because the condom is stretchy, the cock can get larger or smaller, without the Hitachi coming off.
Have fun!!
(25 votes)
|
|
Step 51612 viewsKeep repeating this over-and-under sequence until you have covered several inches of hair.
(28 votes)
|
|
Step 4682 viewsPush the bight through...
(28 votes)
|
|
Step 11694 viewsTo make the ball separator, you will need a few feet of cord, like parachute cord or sash cord. You could probably use long leather bootlaces, but they have a lot more resistance and tend to bite into the skin uncomfortably. And, of course, you will need a cock and some balls. Here we are using a fake cock and balls, since we can't show real ones on the website. The ball separator is a lot more effective and impressive when you are using the real thing.
When you are tying this, be sure to check with your partner about how tight to tie it, since different men like different amounts of tightness and/or pain.
(28 votes)
|
|
Step 7826 viewsBring the free ends around the cock on the opposite side from the loop.
(24 votes)
|
|
Step 3680 viewsIf you look where the two rope ends cross, one of them goes underneath the other one. Take that end and fold it to make another bight. This bight is going to go through the loop we made when we twisted the first bight.
(28 votes)
|
|
Step 122595 viewsBring the two loops together, running them between the balls.
(23 votes)
|
|
Step 11716 viewsStart with a 12-foot length of rope, double it. Reach through the bight (loop), gently grab the hair, and pull it through, so the bight is underneath the hair.
(27 votes)
|
|
Step 131183 viewsNow repeat this sequence as you move up the cock. You don't really have to think about right and left. Just keep one cord zig-zagging on the top, and one cord zig-zagging on the bottom. In this this set of images, I used different color cords for the top and bottom to illustrate this.
(24 votes)
|
|
Step 6613 viewsNow take the end that you just pulled on, and double it to form a bight. This is going to go through the loop we just made.
(23 votes)
|
|
|
|
